Steampunk Jewellery Plier Stands (by Anne)

I have been meaning to decorate my jewellery plier stands for ages and finally got them finished.

I had a bit of a problem with these in that they started off as a plain varnished wood surface. I initially coated them with white Gesso with a view to painting them with acrylics. However, the Gesso did not bind well to the varnish layer – eek! All ideas were halted. These need to be fairly robust and a tonne of flaky chips after a short use was not what I wanted!

I then discovered Powertex and yay, I would be able to rescue and decorate my plier stands after all. Coating the entire surface with rice papers and torn kitchen towels would create a tough protective skin over the surface and prevent the feared chipping off of the base layers.

HOW IT WAS DONE

I first collected together lots of embellishments; die cut cogs and pipework (Sizzix dies), MDF Keyplate (Powertex), metal clock hand and chains, old light bulbs and screws.

I tore out images from Creative Rice Paper (Powertex). This particular sheet seems to be out of stock but there is a similar Victorian Steampunk Paper available. I also separated layers of kitchen paper and tore them into pieces to coat the surface. This would add texture and a protective layer.

STAGE ONE

First I applied the torn decorative papers using Easy Coat Mat Medium. Ivory Powertex was then painted on to blend in the image edges.

STAGE TWO

Next layers of kitchen paper were bonded all over the surface. Some were glued down with Ivory and some with Terracotta Powertex. Die cut card embellishments were also coated with Powertex and glued down.

Texture was added by applying Easy Structure Paste through a texture stencil.

I also had a try at the rust technique. I mixed some Rusty Powder into Ivory Powertex along with a few drops of white wine vinegar. This was painted and dribbled over the surface (extra powder sprinkled on top) and spritzed with water and vinegar before leaving overnight to develop. I spritzed at intervals, several times. I avoided the areas that will be in contact with my pliers. 

STAGE THREE

Next I brushed over and added colour using Acrylic Inks in Tangerine, Egg Yolk, Aqua and Metallic Gold.  

STAGE FOUR

I also applied a little gold Pebeo Gilding Wax on some areas. When fully dry and cured (I left them for 3 weeks) I coated the surface with Easy Varnish to fully seal and protect.

I have included lots of images of how all the surfaces were built up.  

Texture and die cut cogs have been added. 

Rust and colour added. 

Side finished with stronger thick greyboard embellishments. Any large embellishments protruding from edges need to be strong (thinner card would be prone to warp and bend).

I started with a larger clock image on the other side. 

Die cuts and texture added plus a metal clock hand for dimension. 

Finally finished with thicker embellishments and more dry brush work and gilding wax.

Love this character. 

Texture and layers built up. Waiting for the rust to develop. 

Building up the layers of transparent colour makes so much difference.

The second plier stand started off in the same way. 

At this stage you might feel like giving up. What a mess! 

Just keep going, adding layers of rust texture and colour. 

Just loving the gorgeous layers of texture and colour.

I used several layers of the die cut pipework together to make them thicker and stronger on this side.

Wooohooo – this is soooooo yummy (or is it just me – tee hee).

Another end panel. 

I used an MDF keyplate (Powertex) to embellish this end. 

The final colouring makes such a difference.

The final side had a couple of little storage wells. I won’t really be using these so a perfect place to embellish with larger items. 

I had fun adding recycled light bulbs, screws and bits of chain etc. I used structure paste and Powertex treated kitchen paper as a 3D glue to hold things in place. 

Initially I had added a thinner die cut cog to the end but it wasn’t really strong enough. Here I added another thick greyboard cog over the first. Much more practical. I also added a small MDF Butterfly.

Here you can see more of the Steampunk treasures added. I also added some 3D Sand and Balls. 

Love this Steampunk birdie peering out.

Well I hope that all these pictures have not overwhelmed you. I wanted to show how all the stages were built up. It also shows the stages that look awful, perhaps where a beginner might give up! Remember, if it all goes wrong just keep applying colour, inks or coloured varnishes. If this fails and you are really not happy – just paint over the whole thing with a base colour of Powertex and start again.

Hugs, Anne xxx.

Floral Trinket Box created (by Anne)

I have had a wire box frame in my stash for ages. Originally it had a woven straw covering that fell apart so I removed it with the intention of recovering it. It ended up as another ‘UFO’ (unfinished object) for years. I have finally dug it out and created this Powertex treated fabric box embellished with hand made fabric flowers. Now it’s a fabulous trinket box for storing some of my crafty treasures.

The bare wire frame is a strong construction – similar to the type of wire used to make coat hangers. It measures approx. 8 inches square across the top and 6 inches deep.

I used some recycled cotton bed sheets and treated them with Black Powertex to cover the box and lid. I lined the outer and inner panels to completely cover the wire frame. I gathered some cotton trims for the next stage; some crochet lace and a piece of gathered Broderie Anglaise.

I treated the crochet lace with Powertex and applied around the box base.

The gathered lace was applied around the lid. I also dug out some greyboard lazer cut foliage shapes to embellish the top. These were coated and stuck down with Powertex. When dry I started dry brushing over the surface using Easy Varnish and Silver Colotricx. Extra colour was applied to the foliage to make it stand out from the dry brushed background.

Here you can see the dry brushed lid next to the unpainted base. The dry brushing has emphasised the texture and added metallic highlights.

Next I made some fabric roses from 25mm and 15mm strips cut from recycled bedding. These were created using Ribbon Ruching Flower Combs from Gina B-Silkworks. Basically strips are marked out using the Flower Comb templates, a running stitch is sewn along the marked lines and the stitching is pulled up to gather and shape into a rose. I prepared my strips and treated with Powertex before pulling up the stitching. The Powertex holds and glues the gathering in place. I left the flowers to dry before adding to the box top.

I used one of my dies to cut a frame for the centre (Sizzix), applied to the top and finished in the same way as the greyboard foliage.

The flowers were dry brushed with Easy Varnish and Interference Lilac Pigment. Loving these new Pearl Pigment colours! Powertex was then used to glue down the roses to the centre. I added some ready made flower stamens around the group (purple), and some small ready made satin ribbon roses to the corners (Powertex treated and coloured).

Next I mixed some 3D Sand and Balls into Black Powertex and drizzled the mix around the flowers. A few untreated balls were also dropped into the wet Powertex. The untreated balls kept their original colour on the surface giving contrast with the black base. Once dry I coloured by brushing over the surface using Easy Varnish and Mojito Lime Pigment.

I also dry brushed a little of the Lilac pigment sparingly over the lace trims and used to colour some hand made air dry clay embellishments (created using a silicone mould from my stash) added to the box corners.

I used one of my large rubber stamps (lace design from Heartfelt Creations) to stamp some extra textural interest around the sides using Viola Metallic Acrylic Ink. Note: the fabric surface is already quite textured and not very flat so the stamping does not give a clear impression of the design but just adds a little more depth and interest to the surface.

I hope that you like my new treasure box.

Hugs, Anne xxx.

Masquerade Powertex Style

Hi my lovelies, it's really great to have you here. Well this months project pack is absolutely enormous and I didn't even manage to use all of the pieces I still had some left over feathers and fans. Here is the second piece I created to inspire. Hope you have as much creating as I did. 

Top Tip:Always layout your items to give yourself an idea of where they are going to go. And take a photo on your phone to remind yourself. If it changes later on it doesn't matter.

I took some lace and cut it to size so the two fans had some added texture and pattern to them.

Top tip: Use a glue gun to create added dimension to your mdf pieces. My glue happens to be blue so it shows up nicely on the picture.

I also wanted the opening on the mouth to be smaller so snapped either side of the mdf shape and used some Powertex to hold it together in a different position.

I stuck everything down in place on the right side with Bronze Powertex. I used some 3D sand mixed in with the Powertex as some added texture in places. On the left side I used some stone art powder with Ivory Powertex and brown bister to build up a textural layer. And give it as soft stone art effect.

I coated the base layer in Ivory Powertex and mixed some Easy 3D Flex together and spread it across the left side and sprayed with brown bister.

I applied heat with the hair dryer to encourage the cracks to appear. I then dry brushed some Ivory back over the the texture and sprayed more bister and repeated until I was happy with the depth and tones in the finish.

Top tip: The heat from a hair dryer is less intense than a heat gun making it easier to control. 

I stuck the top piece of the mask down to the bottom piece using Transparent Powertex. The Easy 3D base layer is just subtly peaking through in places.

 Then dry brushed the Bronze Powertex with rich gold and bronze gold colortricx and varnish.

Then I just had to add some bling, so placed some gems from my stash on with Transparent Powertex.

And voila. The final result. This one was a little different for me if not ever so subtle. I found it very enjoyable to create a piece that pushed my boundaries though. I can't wait to see your creations do share them with us in the Powertex Studio. And do let us know if you have been inspired by any of the Design Team. We love to hear that you are getting inspiration from our projects. You can find more of my work @RosehartStudio. Toodles Anna xXx